- 您现在的位置：买卖IC网 > Sheet目录1233 > NCP1605LCDTVGEVB (ON Semiconductor)BOARD EVAL NCP1605/1396
NCP1027
clamp is usually selected 50-80 V above the reflected
Power Dissipation and Heatsinking
value N
(V out + V f ). The diode needs to be a fast one and
The NCP1027 hosting a power switch circuit and a
thus evacuate is: P max +
Tj max - Tamb max
an MUR160 represents a good choice. One major
drawback of the RCD network lies in its dependency upon
the peak current. Worse case occurs when I peak and V in are
maximum and V out is close to reach the steady-state value.
Figure 47c: This option is probably the most expensive
of all three but it offers the best protection degree. If you
need a very precise clamping level, you must implement a
Zener diode or a TVS. There are little technology
differences behind a standard Zener diode and a TVS.
However, the die area is far bigger for a transient suppressor
than that of Zener. A 5.0 W Zener diode, like the 1N5388B,
will accept 180 W peak power if it lasts less than 8.3 ms.
If the peak current in the worse case (e.g. when the PWM
circuit maximum current limit works) multiplied by the
nominal Zener voltage exceeds these 180 W, then the diode
will be destroyed when the supply experiences overloads.
A transient suppressor like the P6KE200 still dissipates
5.0 W of continuous power, but is able to accept surges up
to 600 W @ 1.0 ms. Select the Zener or TVS clamping
level between 40 to 80 V above the reflected output voltage
controller, it is mandatory to properly manage the heat
generated by losses. If no precaution is taken, risks exist to
trigger the internal thermal shutdown (TSD). To help
dissipating the heat, the PCB designer must foresee large
copper areas around the PDI7 package. When surrounded
by a surface greater than 1.0 cm @ of 35 m m copper, it
becomes possible to drop the thermal resistance
junction-to-ambient, R q JA down to 75 ° C/W and thus
dissipate more power. The maximum power the device can
(eq. 22)
R q JA
which gives around 930 mW for an ambient of 50 ° C and a
maximum junction of 120 ° C. The losses inherent to the
switch circuit R DS(on) can be theoretically evaluated, but
the final prototype evaluation must include board
measurements to confirm that the junction temperature
stays within safe limits. Figure 48 gives a possible layout
to help dropping the thermal resistance. When measured on
a 70 m m (2 oz.) copper thickness PCB, we obtained a
thermal resistance of 75 ° C/W.
when the supply is heavily loaded.
Figure 48. A possible PCB arrangement to reduce the thermal resistance
junction-to-ambient.
When routing the printed circuit, it is important to keep
high impedance line very short, like the brown-out signal
and the OPP input if used.
Application Diagram
Figure 49 displays the final application schematic. The
output uses a TLV431 whose low bias current represents an
advantage for low standby power switch mode supplies.
The secondary side features an additional LC filter needed
to remove unwanted spikes, although less problematic than
in DCM operation. On the primary side, a resistive network
senses the input bulk voltage and prevents the controller
from turning on for input voltages below 100 Vdc. The
auxiliary winding delivers 20 V nominal and thus offers
comfortable margin when the converter enters standby. As
we do not use any OPP, pin 7 goes to ground and offers
extended possibility to layout more copper area.
http://onsemi.com
27
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NCP1608BOOSTGEVB
BOARD EVAL NCP1608 100W BOOST
NCP1631PFCGEVB
BOARD DEMO NCP1631 INTERLEAV PFC
NCP1650EVB
BOARD EVAL NCP1650 PFC CTLR
NCP1652L48VGEVB
BOARD EVAL 100W 48V NCP1652 PFC
NCP1653EVB
BOARD EVAL FOR NCP1653
NCP2993FCT2GEVB
BOARD EVAL NCP2993 AUDIO PWR AMP
NCP345SNT1G
IC DETECTOR OVER VOLTAGE 5TSOP
NCP346SN2T1G
IC DETECTOR OVER VOLTAGE 5TSOP
相关代理商/技术参数
NCP1606ADR2G
功能描述:功率因数校正 IC PWR FCTR CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606APG
功能描述:功率因数校正 IC LO CST PWR FCTR CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606BDR2G
功能描述:功率因数校正 IC PWR FCTR CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1606BOOSTGEVB
功能描述:电源管理IC开发工具 OSPI NCP1606 100 W BOOST
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP1606BPG
功能描述:功率因数校正 IC LO CST PWR FCTR CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1607BDR2G
功能描述:功率因数校正 IC CST EFCT PW FCTR CTR RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
NCP1607BOOSTGEVB
功能描述:BOARD EVAL NCP1607 100W BOOST RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板
NCP1608BDR2G
功能描述:功率因数校正 IC COST EFFECT PWR FACT CONT RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel